#Freepbx sip setup install
#Freepbx sip setup registration
#Freepbx sip setup code
#Freepbx sip setup password

> Scroll to Trunk Sequence and select the SIP/IsraelNumber trunk from the drop-down list > Enter to-IsraelNumber into Route Name field > Click on Outbound RoutesВ to configure your Asterisk box to send calls to IsraelNumber. If using FreePBX you will need to log in to your server and edit the /etc/asterisk/sip.conf file manually, usually with an editor such as Putty / Nano or such.ДЄn outbound route sends calls that are dialed in a certain pattern to your provider, IsraelNumber. > Now you will want to edit your sip.conf file and enter, or modify, the following lines: > Click on the red bar at the top of the screen to apply the changes you just made > Click on Submit ChangesВ to add your new SIP trunk to your Asterisk server

#Freepbx sip setup password

Optionally you may change your password in your preferences.

#Freepbx sip setup registration

> Enter your registration string in this YourUserName and YourPassword were given to you by IsraelNumber at the time of registration. Optionally you may change YourPassword in your preferences. Where YourUserName and YourPassword were given to you by IsraelNumber at time of registration. > Copy and paste the following into the PEER DetailsВ field: > Scroll to Outgoing SettingsВ and enter IsraelNumberВ into Trunk NameВ field > Click Add SIP Trunk in middle of the page > Click on Trunks in the left side navigation > Click on Setup in the top right of the page > Login to FreePBX administrative interface In this section, we will configure a SIP trunk. In the context of this guide a trunk is used to route calls between your Asterisk PBX and your desired VSP(Voice Service Provider), in this case, IsraelNumber. We recommend that you read each step through in its entirety before performing the action indicated in the step.

#Freepbx sip setup install

This guide also assumes that the FreePBX install steps were completed properly and that you have administrative access to the FreePBX administration interface. This guide assumes that you have installed FreePBX using either the FreePBX package or a method of your choice. The setup information below is based on FreePBX 2.1.3 although most other older and newer versions will look very similar.Д¬onfiguring the Asterisk PBX using the FreePBX interface Installing the account details given to you by us at sign up will allow you to send and receive calls using us as your provider.

Be sure to Submit your changes in the bottom right and after the page reloads Apply ConfigВ in the top right to save and apply your Changes.Using FreePBX you are able to do most of AsteriskвЂ™s configuration without editing the individual configuration files.

To create the Secondary Registration it is the same process, but set the SIP Server in step 6.e to the second server listed under Registrations found on your Dashboard in the Clearly IP Trunking Store.

On the 'Advanced' tab of the 'pjsip Settings' tab you will need to set:.

Note: When you setup the Secondary Registration your will use the second server listed.

Set the SIP Server to be first one listed under Registrations found on your Dashboard in the Clearly IP Trunking Store.

Verify Authentication is set to Outbound.

Set the SecretВ to the Sip Credentials Password found on your Dashboard in the Clearly IP Trunking Store.

Set the UsernameВ to the Sip Credentials Username found on your Dashboard in the Clearly IP Trunking Store.

On the 'General' tabВ of the 'pjsip Settings'В tab you will need to set:.

#Freepbx sip setup code

Prepend=1NPA and Match Pattern=NXXXXXX where NPA is the local area code for the PBX

If you want to enable 7 Digit Dialing you would do so by adding a second Dial Pattern of.On the 'Dialed Number Manipulation Rules' tab, set a Prepend of 1 for NXXNXXXXXX.That will enable calls to fail to other Trunks/Carriers if you have them. If you are not using concurrency bursting, you can set this to match your number of Call Paths.If you have concurrency bursting enabled on your ClearlyIP Trunks you can leave this blank or set it to the absolute maximum calls you think would be reasonable for your environment.This will be the default Caller ID for any Calls going out this Trunk. ClearlyIP-Trunk1), this is the descriptive name for the Trunks. Select 'Add SIP (chan_pjsip) Trunk' from the Add Trunk drop down.Login to the Admin GUI of your FreePBXВ©.